We are the world class engineering manufacturer providing the highest quality products, services and solutions to our customers.

c1

Testing Facilities (Material Testing Labs)

All products undergo through inspection and tests by out Quality Assurance Department at varios stages of manufacturing according to internationally established inspection procedures and methods. HMC is equipped with both destructive and non-destructive testing facilities and a metrological laboratory. 

MECHANICAL TESTING

Tensile testing of metallic materials on Universal Testing Machines (10 Tons, 30 Ton Tons, 60 Ton and 100 Tons)
Hardness testing , Bench type  and portable (Rockwell,Brinnel and Vicker)
Bend testing of metallic materials.
Charpy Impact Testing both at room temp and below zero
Charpy Impact Testing Machine 15/30 Kg-m/CM2
Compression Strength of refractory materials

CHEMICAL TESTING

i. Spectrometric

The department has unique installation of most modern spectrometer (Spectromax Germany of 26 elements) for analysis of Iron/ Steel and Copper based materials / alloys, adjacent to the melting section of HMC to provide accurate reliable and fast track analysis in a  minimum time,  since good process control requires prompt feed back.

ii. Wet Chemistry/analysis

All foundry inputs such as Ferro Alloys (Ferro Silico, Ferro Manganese, Ferro Chrome, Ferro Nickel & Ferro Vanadium etc), Al, Ni, Cu, Tin, Lead and their alloys are got checked before being incorporated into production function, in addition to these following testing facilities are also available.

–              Physical & chemical testing of silica sand and Bentonite Clay.
–              Refractory Materials of all kinds
–              Sodium Silicate, Water and Oil etc

iii. Equipment and machinery

  1. Mill Grindinder RS 1 Retsch Germany 700-1400 RPM
  2. Carbolite Muffle Furnace England , max temp 1500degree centigrade
  3. Electrolytic Analyzer Chinese
  4. Electronic Balance max weighing cpacity 150gms, readability 0.001gm
  5. Heating Furnace max temp 1340 degree centigrade
  6. Muller for bentonite sample preparation Ridsdale & Co, UK
  7. Seive Shaker Ridsdale & Co. UK
  8. Speedy Moisture Tester 0-20%
  9. Strength Tester ,Ridsdale & Co 0-1.3 kg/cm 2

(iv) Calibration

HMC has the facility of repair and calibration of instruments like:-

–      Pyrometers, pressure gauges, thermocouples, temperature indicators, meggers , avometers, voltmeters, dial indicators, vernier calipers, micrometers, sprit levels, steel taps and steel rules etc.

METROLOGY

Measurements

Metrology section has precision machines like:-
–      Projector JTT-500-II , ( 200 x100 / 0.001 mm)
–      Microscope Type JGX3 (200×100/0.001mm)
–      Metroscope JD-5
–      3 Meter length measuring machine JD-10 (0-3 meter/0.001 mm) and others for the measurement of

  1. Various templates, gauges manufactured for use in production.
  2. Sizes of components which can not be measured by ordinary methods.

METALLOGRAPHIC TESTING

  • Macro Etching Metals & Alloys 

–    For the examination of segregation, weld quality, pinholes etc.

  • Micro Examination for

–    Identification of microstructure
–    Grain size determination
–    Examination of Internal cracks
–    Detection of Non Metallic Inclusions
–    Process control 

  • Equipment and machinery 
  1. Specimen Polisher/grinder ROTOPOL-25, Denmark max speed 600 rpm
  2. Specimen grinding machine Chinese, rpm 410/550
  3. Metallographic polisher Chinese rpm 1350
  4. Microhardness Tester Chinese HS-I , x 130-487
  5. Metallurgical Microscope (Brightfield/darkfield) with camera attachment Model 7530 , Meiji Japan upto x 1000
  6. Metallurgical Microscope Chinese XJB-I , x 1500-02 Nos
  7. Metallurgical Microscope Model XJG-4 , x 1600
  • Harden ability End Quench Test

For determining depth of hardness of harden- able steels
Using  Meta Serve End Quench Unit (Buhler UK)

  • Mc-QUAID EHN Test:  for  determination of Austenite  grain size of steel

HYDROSTATIC TESTING

Hydrostatic testing up to 150 bars pressure can be carried out with the existing facility

PNEUMATIC TESTING

Pneumatic testing up to 7 kg/cm2 can be carried out with existing facility

The safety policy of Heavy Mechanical Complex, Taxila is based upon:-

Importance of safety is pre-requisite and cannot be ignored. Human life is valuable and ought to be protected by all means. Besides human life the safety of plant Machinery and other operative equipment is also important. Safety is not an individual’s concern rather it is observed collective efforts and is the responsibility of everybody. It needs attention by everyone at all times. Conduct of routine safety surveys is a routine practice to find and eliminate unsafe working conditions and control hazards. Our company is committed to take reasonable effort to eliminate the hazards that cause accident and injury. We are committed to continuing improvement toward an accident free workplace through effective Administration, Education and Training. Safety procedure/instructions described in Safety Manual of the company are based on international safety practices. These instructions are displayed at all the relevant/ concerned area of activity and mandatory for all the employees. Safety Officer nominated by the Managing Director along with all the heads of department will be responsible for the implementation of Safety Manual of the company.

Our Vision

“To undertake Structural and Financial reforms to transform HMC into a vibrant, self-sustained and modern business enterprise; a progressive manufacturing concern to support and develop Country’s industrial and infrastructure growth”

Our Mission

“Be the leading Engineering Enterprise that shall have the capability to develop industrial sectors, through acquisition of technology and diversification”

The quality policy of Heavy Mechanical Complex is based upon: “Quality performance is a commitment to excellence by each company employee, it is achieved by team work and through a process of continuous improvement and compliance of applicable legal and quality management system (ISO 9001:2015) requirements.” “We are dedicated to being seen as an organization which provides quality products and services which meet or exceed the expectations of our clients and relevant interested parties.”

Heavy Mechanical Complex Limited is a leading engineering goods manufacturing enterprise in Pakistan located at Taxila about 30 Kilometers north of capital Islamabad. It is a professionally managed progressive organization with over 160,000 sq. meters covered facilities.

It has the resources to handle large projects with demanding delivery schedules. Being the largest and most extensive fabrication and machining facility equipped with state of the art technology HMC provides manufacturing services both on its own or customers design.

HMC has gained rich experience in designing and manufacturing of large projects through collaboration with internationally reputed engineering organizations. All its processing facilities are in-house including Designing, Fabrication, Machining, Iron and Steel Castings, Forgings, Heat Treatment, Assembly, Sand Blasting, Painting and Galvanizing etc.

ISO 9001 - Since 1997

HMC is ISO 9001 certified and is authorized to use ASME stamps U, U2, S & PP for equipment manufactured according to ASME code.
The manufacturing is backed by excellent quality control and testing facilities to meet the product and customer quality requirements.
3rd party inspection facilities are also available, where required.

ASME

ASME Stamps U, U2, S, PP, R, for Pressure Vessels, Power boilers, Pressure piping 

Lloyds of U.K

Certified Manufacturer of 1st Class Fusion Welded Pressure Vessels